| Author |
Message |
 Topic: How to disable WOT shift settings? |
JesseN
Replies: 3
Views: 332
|
 Forum: Technical Support Posted: Wed Jun 18, 2008 8:17 am Subject: How to disable WOT shift settings? |
It's version 1.19.12 (older one I believe).
So 100% will disable it then?
Thanks |
| Topic: How to disable WOT shift settings? |
JesseN
Replies: 3
Views: 332
|
Forum: Technical Support Posted: Mon Jun 16, 2008 12:14 pm Subject: How to disable WOT shift settings? |
| I want to ensure I don't use the WOT shift settings in the controller since I have no rpm input. If I set the "% throttle to use WOT setttings" to 100%, does this ensure the individual shift tables a ... |
| Topic: TCC unlock during shifts (how to?) |
JesseN
Replies: 11
Views: 1322
|
Forum: Technical Support Posted: Tue Feb 12, 2008 4:21 pm Subject: TCC unlock during shifts (how to?) |
| hope to try it this weekend, have to borrow a laptop again... |
| Topic: TCC unlock during shifts (how to?) |
JesseN
Replies: 11
Views: 1322
|
Forum: Technical Support Posted: Mon Feb 04, 2008 12:19 pm Subject: TCC unlock during shifts (how to?) |
Sorry, can't see the pic. Send it to my email jdnedde (at) nppd.com
Thanks |
| Topic: TCC unlock during shifts (how to?) |
JesseN
Replies: 11
Views: 1322
|
Forum: Technical Support Posted: Mon Feb 04, 2008 11:54 am Subject: TCC unlock during shifts (how to?) |
I have also set the TC Lockup at about 2 or so MPH lower than the shift point for that gear and it will shift into 3rd unlocked and then will lockup after the shift.
I'm alittle confused by this st ... |
| Topic: TCC unlock during shifts (how to?) |
JesseN
Replies: 11
Views: 1322
|
Forum: Technical Support Posted: Mon Feb 04, 2008 9:20 am Subject: TCC unlock during shifts (how to?) |
| Yes, using the standalone valvebody from ATS. I have the datalog somewhere around here. It doesn't show any attempt to unlock the TC... If I can find it, I will email it to you. |
| Topic: TCC unlock during shifts (how to?) |
JesseN
Replies: 11
Views: 1322
|
Forum: Technical Support Posted: Sun Feb 03, 2008 1:50 pm Subject: TCC unlock during shifts (how to?) |
| Based on the datalogging I did, it appears the buttons to unlock during shifts has no affect on the TC (atleast in a 48re application). It appears to be solely based upon the lockup tables/speeds fil ... |
| Topic: TCC unlock during shifts (how to?) |
JesseN
Replies: 11
Views: 1322
|
Forum: Technical Support Posted: Thu Jan 10, 2008 6:36 pm Subject: TCC unlock during shifts (how to?) |
| I called in and spoke with Dan today. I am going to datalog it and see what is going on. |
| Topic: TCC unlock during shifts (how to?) |
JesseN
Replies: 11
Views: 1322
|
Forum: Technical Support Posted: Wed Jan 09, 2008 7:30 pm Subject: TCC unlock during shifts (how to?) |
| I have tried using both the lockup per gear as well as the normal lockup. Either way I can setup at what speed and/or tps to lockup the convertor (and also unlock it). No problems there. My problem ... |
| Topic: Can the CAN BUS be used to get inputs like TPS & RPM, et |
JesseN
Replies: 7
Views: 900
|
Forum: Technical Support Posted: Wed Dec 12, 2007 5:11 pm Subject: Can the CAN BUS be used to get inputs like TPS & RPM, et |
I believe I did, it seemed to do everything it needed for the conversion and just asked a simple yes or no to proceed. I didn't do anything that it didn't ask for on the screen though.
I do have b ... |
| Topic: Can the CAN BUS be used to get inputs like TPS & RPM, et |
JesseN
Replies: 7
Views: 900
|
Forum: Technical Support Posted: Fri Dec 07, 2007 4:34 pm Subject: Can the CAN BUS be used to get inputs like TPS & RPM, et |
| Well I went ahead and tried it. Upgraded firmware on the controller, upgraded the calibration file. Everything seemed to convert ok. However, any time you try to click on anything on the left hand ... |
| Topic: Can the CAN BUS be used to get inputs like TPS & RPM, et |
JesseN
Replies: 7
Views: 900
|
Forum: Technical Support Posted: Thu Dec 06, 2007 2:29 am Subject: Can the CAN BUS be used to get inputs like TPS & RPM, et |
| Well, just to try it I downloaded the latest software here at home. I see alot more options on it compared to my old one. I found the CAN comm stuff. It looks like I can get TPS, RPM, Coolant temp, ... |
| Topic: Can the CAN BUS be used to get inputs like TPS & RPM, et |
JesseN
Replies: 7
Views: 900
|
Forum: Technical Support Posted: Thu Dec 06, 2007 1:57 am Subject: Can the CAN BUS be used to get inputs like TPS & RPM, et |
| Yes it is J1939 CAN BUS. I am wondering if I need to download the latest software to use this. My current version of the TCU software is 1.19.12. My understanding is that ATS markets the controller ... |
| Topic: Can the CAN BUS be used to get inputs like TPS & RPM, et |
JesseN
Replies: 7
Views: 900
|
Forum: Technical Support Posted: Wed Dec 05, 2007 7:55 pm Subject: Can the CAN BUS be used to get inputs like TPS & RPM, et |
I read about it in the manual however I can't find any CAN communication form (as it is listed in the manual p58) in the software?
BTW, I'm controlling a 48RE behind a 5.9 cummins (electronic contr ... |
| |
Forum FAQ
Search
Usergroups
Profile
Log in