| Author |
Message |
 Topic: When is the TCU going to be available for the 722.6 tranny? |
Russ
Replies: 24
Views: 3207
|
 Forum: News & General Discussion Posted: Sun Oct 19, 2008 12:39 am Subject: When is the TCU going to be available for the 722.6 tranny? |
John,
It is possible for us to setup the controller to receive VSS and TPS over CAN if someone has access to the factory CAN message structure. It looks like we are going to be discontinuing suppor ... |
| Topic: Aisin a761E transmission |
Russ
Replies: 1
Views: 28
|
Forum: News & General Discussion Posted: Sat Oct 18, 2008 11:27 pm Subject: Aisin a761E transmission |
T,
We don't have any information available for that transmission. It would be difficult to determine if our controller would be compatible with it.
Russ |
| Topic: Another Speed Senor Hookup Question |
Russ
Replies: 2
Views: 59
|
Forum: Compatibility & Settings Posted: Tue Oct 07, 2008 9:53 am Subject: Another Speed Senor Hookup Question |
| On the Nissan 240sx we have here the settings are. Pull up resistor enabled, 2 pulses per rev, tire size, axle ratio, trigger level 2.5, filter 2, glitch filter 3. We connected one side to speed input ... |
| Topic: Version 2.5.6 Vs Ver 2.9.0 |
Russ
Replies: 2
Views: 49
|
Forum: Technical Support Posted: Tue Oct 07, 2008 9:48 am Subject: Version 2.5.6 Vs Ver 2.9.0 |
Tim,
Yes it includes all the previous additons. There won't be anything you'll notice is different. We added support for CAN based shifters and some other minor stuff.
Russ |
| Topic: TCC lock |
Russ
Replies: 3
Views: 82
|
Forum: Calibration/Tuning Posted: Tue Oct 07, 2008 9:44 am Subject: TCC lock |
| The TCC lockup is controlled by line pressure also. If the line pressure is too low you don't get good control. I would increase your 3-4 line pressure to correct the hanging on the 3-4 shift first. T ... |
| Topic: Can I use the new Firmware and Software? |
Russ
Replies: 2
Views: 86
|
Forum: Technical Support Posted: Sun Aug 24, 2008 1:49 am Subject: Can I use the new Firmware and Software? |
You can upgrade to the new software with the ATS VB. Make sure to save your calibration before you get started in case you need to go back.
Russ |
| Topic: XFC for a GMC Typhoon |
Russ
Replies: 1
Views: 119
|
Forum: News & General Discussion Posted: Thu Aug 21, 2008 10:08 pm Subject: XFC for a GMC Typhoon |
It depends on what you need to do. If your vehicle is a mass air flow system you can use it for tuning the air fuel ratio and manipulating the oxygen sensors.
Russ |
| Topic: Auxillary transmission control |
Russ
Replies: 1
Views: 337
|
Forum: News & General Discussion Posted: Thu Aug 21, 2008 10:04 pm Subject: Auxillary transmission control |
Marvin,
Our controller will not work with the US gear overdrive if you have to let off for it to shift. The TCU can not force the engine to let off for you. You can still use the overdrive but yo ... |
| Topic: 2.0 Mazda 3 issues |
Russ
Replies: 1
Views: 138
|
Forum: Technical Support Posted: Fri Aug 15, 2008 11:09 pm Subject: 2.0 Mazda 3 issues |
Have you tried just disconnecting the coil pack from the XFC to see if the car runs correctly? The coil pack wire is just used for measuring rpm. Do your coils have 2 wires or 3 wires?
Russ |
| Topic: truck barely moves, HELP race today, new TCU user |
Russ
Replies: 3
Views: 146
|
Forum: Technical Support Posted: Sat Aug 09, 2008 8:45 pm Subject: truck barely moves, HELP race today, new TCU user |
| I'm assuming its the ATS or Sun Coast Converters valve body, as our controller will not work on a stock 47re. On the ATS valve body pressure is controlled by the cable and not by our controller. I sug ... |
| Topic: 4T65E won't shift, gear indicator doesn't change from 1 |
Russ
Replies: 3
Views: 128
|
Forum: Technical Support Posted: Sat Aug 09, 2008 12:04 pm Subject: 4T65E won't shift, gear indicator doesn't change from 1 |
Jon,
They would need to be configured if they are defined as Gear Selects in the Digital Input Chart. If you disable them in the digital input chart you will have to reset the unit before it will w ... |
| Topic: truck barely moves, HELP race today, new TCU user |
Russ
Replies: 3
Views: 146
|
Forum: Technical Support Posted: Sat Aug 09, 2008 11:59 am Subject: truck barely moves, HELP race today, new TCU user |
What kind of transmission is this? Is this a Diesel truck?
Russ |
| Topic: ZF 6HP26, 6R60, 6R80 |
Russ
Replies: 1
Views: 255
|
Forum: News & General Discussion Posted: Fri Aug 01, 2008 4:56 pm Subject: ZF 6HP26, 6R60, 6R80 |
| We are working on a controller for the GM 6L80 transmission. Its not likely we will do the 6HP or 6R transmissions. Its extremely difficult to accomplish and the market is not really there. Its possi ... |
| Topic: cal problems |
Russ
Replies: 1
Views: 166
|
Forum: Calibration/Tuning Posted: Fri Aug 01, 2008 4:51 pm Subject: cal problems |
After typing in a number press Enter. If not the setting will go back to what it was. Also, if your connected to the unit when you press enter the unit will be updated to match the new setting.
Rus ... |
| Topic: A343 TEMPLATE |
Russ
Replies: 1
Views: 72
|
Forum: Calibration/Tuning Posted: Thu Jul 24, 2008 9:36 pm Subject: A343 TEMPLATE |
Let me email you a new file. I'm not sure why that calibration would only have 3 inputs configured for gear selects. You should have a digital input for each position on that transmission.
Russ |
| |
Forum FAQ
Search
Usergroups
Profile
Log in